GRR-RIPPER MAX

GRR-RIPPER 3D Pushblock Max

Don't use a table saw without it.®:

The Grr-ripper®: Max is an all-in-one package for ultimate control, precision, and safety. The package includes a Grr-ripper®: Max 3D Pushblock and one of every accessory we make for it. It's everything you need to experience the full range of functionality that only the Grr-ripper®: can offer.

Microjig Founder and inventor, Henry Wang, started in his garage workshop in the late 90s. Faced with the challenge of cutting thin strips on a table saw, he sought to create a solution to cut small parts safely, accurately, and consistently. After countless engineering hours and dozens of prototypes, the Grr-ripper®: pushblock was born.

Protect your hands during the entire cut.

• Center Leg
  Adjusts to varying material widths, allowing you to control both the keeper and off-cut sides of your workpiece through the entire cut.
• Balance Support
  Adjusts to match material thickness, keeping the Grr-ripper®: upright and square.
• Green Grr-rip®:
  Offers incredible traction and control over hardwoods, composites, plastics, and aluminum. This treaded surface conforms to your workpiece, providing superior control and stability.

Virtually eliminate kickback on table saws.

The Grr-ripper's 3-directional force system applies downward, inward, and forward pressure to your workpiece. The three forces stabilize your material from every angle and keep both sides of the cut parallel to the blade. This feature prevents the workpiece from straying from the rip fence to virtually eliminate kickback.

Kickback occurs when either side of your workpiece strays from the fence and gets pinched between the saw blade and the fence. The rear teeth of the blade grab the workpiece, turning it into a dangerous projectile.

Create your own clamp tracks.

With MatchFit, you're not confined to pre-set clamp positions. Carve out your custom dovetail tracks on any wooden surface, enhancing your hold-down capabilities where you need them most. The Dovetail Track System gives you all the functionality of T-track, in less time and at a fraction of the cost.

Seamless dovetail integration: All MatchFit clamps slide into any 1/2 in. x 14° dovetail groove, transforming your setup into a unified clamping haven for unmatched efficiency.

Rip without stopping or burning.

Using two Grr-rippers allows you to feed long stock continuously without stopping, virtually eliminating burning and blade marks caused by inconsistent feed rate. Parts come off the saw ready to use with little to no additional sanding or planing.

Complete precision, control, and safety.

Includes all Grr-ripper Pro upgrades:

• The Adjustable Spacer gives you 54% more gripping surface for larger workpieces and provides clearance for exposed router bits.
• The Stabilizing Plate provides 250% more stabilizing surface and keeps the workpiece locked against the fence. The rear hook pushes the tail end of your workpiece.

The new SafeRip Kit enhances your Grr-ripper's safety features by preventing accidental blade contact with the Center Leg. The SafeRip Kit guides your setup, ensuring the Center Leg is always positioned safely away from the blade.

The 1/8 in. Leg allows you to rip thin strips down to â…› in., safely and repeatably.   Excellent for edge banding, models, or decorative inlays.

The Gravity Heel Kit provides dynamic sacrificial heels that automatically retract mid-board, and drop down to hook the tail end of the workpiece. The specially material allows them to  be cut, providing support to prevent tearout.

The Handle Bridges distribute downward pressure evenly for greater control and safer cuts.   You'll notice the difference.

The Deflector / Connector acts as a barrier between your hands and spinning blades while deflecting chips and debris.   It also connects to GRR-RIPPERs equipped with Handle Bridges.   Two GRR-RIPPERs mean twice the control while working with larger workpieces.

Use it around your whole shop.

Over 30+ uses on table saws, router tables, jointers, and band saws.

Router Tables

The Grr-ripper provides incredible command over your workpiece on the router table. Whether you're using the fence or freehand routing, its powerful grip controls stock and protects your hands from dangerous spinning bits.

Table Saws

The Grr-ripper was built for the table saw. It acts as a moving blade guard, shielding your hands from the saw blade through the entire cut. Right out of the box, the Grr-ripper can cut stock down to ¼ in. x ¼ in. Because it provides three directions of control, your cuts will be cleaner and more precise.

Jointers

The Grr-ripper's proprietary Green Grr-rip material provides all the traction you need to flatten stock on the jointer properly. Because of its powerful grip, you can feed material over the cutter head without having to apply too much downward pressure.   The Grr-ripper makes proper face-jointing technique easy and safe.

Band Saws

The Grr-ripper's legs and main body maintain a constant 90-degree angle. It can be used on its side, which is ideal for resawing on band saws. The Grr-ripper glides along the table top and applies even pressure against the fence with your hands clear of the blade. Even pressure means less blade drift, resulting in smoother cuts.