MATCHFIT Dovetail Router Bit - 1/4 in. Shank
For Use with Router, Router Table, MATCHFIT Dovetail Clamps
MATCHFIT Dovetail Router Bit 1/4 inch Shank
The MATCHFIT Dovetail Router Bit is specifically designed for the match-fit Dovetail clamps and Dovetail hardware.
Its unique design uses the same standard 14-degree, 1/2 in. profile, but with rounded corners. It routes incredibly clean Dovetail grooves and requires less sanding, making the match-fit system faster and easier. Down Shear - the 8-degree down Shear utilizes the bit's rotation to evacuate chips and dust, reducing friction and heat and resulting in cleaner cuts.
Bottom round over - the bottom of the Dovetail Groove Bears most of the clamping pressure. The 1/32 in. round over strengthens that bottom corner by removing less material. This is especially important when routing grooves in plywood, as it minimizes the possibility of plies separating. Top round over - the 1/16 in. round over at the top of the Dovetail Groove has several functions. Firstly, it prevents tear-out and fuzz, significantly reducing the sanding needed. It also provides a range of tolerance. The bit can be set to a depth anywhere between .365 in. and .385 in. and still be fully compatible with the match-fit line of products.
Within that range, the width of the Groove opening at the top will remain the same but with varying round-over exposure. The shallower the Groove, the smaller the round over. The deeper the Groove, the more pronounced the round-over will be. Laser cut, the depth guideline is exactly 3/8 in. from the end of the carbide Cutter. With the depth guideline, even with the material's surface, the bit will cut a .375 in. deep Groove, which is in the middle of its tolerance range.
Wide base - the wide base reduces vibration and noise while routing grooves, resulting in smoother, cleaner cuts. Router collet safety line - the router collet safety line shows how deep the bit should be into the collet. The bit's shank was designed to be as long as possible while fitting into any major manufacturer's router. This provides more surface area for the collet to grip, reduces vibration for a smoother cut, and minimizes the risk of the bit loosening and ejecting from the router.
The MATCHFIT Dovetail Router Bit is specifically designed for the match fit Dovetail clamps and Dovetail hardware.
Its unique design uses the same standard 14-degree 1/2 in. profile, but with rounded corners. It routes incredibly clean Dovetail grooves and requires less sanding, making the match-fit system faster and easier. Down Shear - the 8-degree down Shear uses the bit's rotation to evacuate chips and dust, reducing friction and heat and resulting in cleaner cuts.
Bottom round over - the bottom of the Dovetail Groove bears the majority of the clamping pressure. The 1/32 in. round over strengthens that bottom corner by removing less material. This is especially important when routing grooves in plywood, as it minimizes the possibility of plies separating. Top round over - the 1/16 in. round over at the top of the Dovetail Groove has several functions. Firstly, it prevents tear out and fuzz, significantly reducing the sanding needed. It also provides a range of tolerance. The bit can be set to a depth anywhere between .365 in. and .385 in., and still be fully compatible with the match-fit line of products.
| Product Group | Router Bits |
|---|---|
| BRAND | Micro Jig |
| SHANK SIZE | 1/4 in. |
| GUIDE POSITION | None |
| QUANTITY | (1) Each |
| SKU | MJ-MB-025-0514 |
| SPECS: |
|
| Prop 65 |
WARNING: This product can expose you to chemicals including Styrene, which is know to the Sate of California to cause cancer. For more information, visit www.P65Warnings.ca.gov.
|
WARNING: This product can expose you to chemicals including Styrene, which is know to the Sate of California to cause cancer. For more information, visit www.P65Warnings.ca.gov.
WARNING: While working in a hazardous area where you can be exposed to flying objects, fragments, and particles, primary protective devices such as safety glasses or goggles with side shields must be worn. Secondary protective devices such as a face shield is required in conjunction with primary protective devices during severe exposure to impact hazards.
WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.
Login and Registration Form