GRR-RIPPER +
GRR-RIPPER+ 3D Pushblock
Don't use a table saw without it.®:
The Grr-ripper 3D Pushblock is engineered to give you the most accurate cuts possible while protecting your hands at all times. No other pushblock offers this level of precision, control, and safety. Make difficult cuts with ease and prevent kickback like never before.
Three directions of force.
Three directions of force provide essential stability for superior precision, safety, and control.
- Downward pressure stabilizes work piece on a flat surface.
- Inward pressure against the fence virtually eliminates kickback.
- Forward pressure feeds stock consistently through the cut to eliminate burning and blade marks.
Virtually eliminates kickback on table saws.
Kickback occurs when the workpiece strays from the fence and gets pinched between the saw blade and the fence. The rear teeth of the blade grab the workpiece, turning it into a dangerous projectile. The only way to avoid kickback is to maintain control of your workpiece through the entire cut.
The Grr-ripper provides downward and inward pressure, keeping both sides of the cut parallel to the blade. This prevents the workpiece from straying from the rip fence, virtually eliminating kickback.
Create your own clamp tracks.
With MatchFit, you're not confined to pre-set clamp positions. Carve out your custom dovetail tracks on any wooden surface, enhancing your hold-down capabilities where you need them most. The Dovetail Track System gives you all the functionality of T-track, in less time and at a fraction of the cost.
Seamless dovetail integration: All MatchFit clamps slide into any 1/2 un. x 14° dovetail groove, transforming your setup into a unified clamping haven for unmatched efficiency.
Rip without stopping and burning.
Using two Grr-rippers allows you to feed long stock continuously without stopping, virtually eliminating burning and blade marks caused by inconsistent feed rate. Parts come off the saw ready to use with little to no additional sanding or planing.
Protect your hands and fingers.
The benchmark for safety, precision, and control.
Prevent Blade Contact
SafeRip Kit NEW
Prevent cutting your Grr-ripper Center Leg at the table saw. The rip width guides the Center Leg setting. If your cut shows under the cursor, move the Center Leg. No leaning over to check the cut settings, and quicker setups with no check passes.
Fully Adjustable
Center Leg
Adjusts to varying material widths, allowing you to control both the keeper and off-cut sides of your workpiece through the entire cut.
Balance Support
Adjusts to match material thickness, keeping the Grr-ripper upright and square.
Ultimate Gripping Power
Green Grr-ripâ„¢ gives you incredible traction for easy handling of hardwoods, composites, plastics, and aluminum. Its treaded surface conforms to the workpiece for superior control.
Dust and buildup easily wipe off with denatured alcohol. The additional 1 un. of Green Grr-ripâ„¢ on the Adjustable Spacer provides even more traction for advanced control.
Use it around your whole shop.
Over 30+ uses on table saws, router tables, jointers, and band saws.Router Tables
The Grr-ripper provides incredible command over your workpiece on the router table. Whether you're using the fence or freehand routing, its powerful grip controls stock and protects your hands from dangerous spinning bits.
Table Saws
The Grr-ripper was built for the table saw. It acts as a moving blade guard, shielding your hands from the saw blade through the entire cut. Right out of the box, the Grr-ripper can cut stock down to ¼ in. x ¼ in.. Because it provides three directions of control, your cuts will be cleaner and more precise.
Jointers
The Grr-ripper's proprietary Green Grr-rip material provides all the traction you need to flatten stock on the jointer properly. Because of its powerful grip, you can feed material over the cutter head without having to apply too much downward pressure. The Grr-ripper makes proper face-jointing technique easy and safe.
Band Saws
The Grr-ripper's legs and main body maintain a constant 90-degree angle. It can be used on its side, which is ideal for resawing on band saws. The Grr-ripper glides along the table top and applies even pressure against the fence with your hands clear of the blade. Even pressure means less blade drift, resulting in smoother cuts.
| BRAND | MICROJIG |
|---|---|
| QUANTITY | (1) Each |
| SKU | MJ-100Plus |
| Prop 65 |
WARNING: This product can expose you to chemicals including Vinyl Chloride, which is know to the Sate of California to cause cancer. For more information, visit www.P65Warnings.ca.gov.
|
WARNING: This product can expose you to chemicals including Vinyl Chloride, which is know to the Sate of California to cause cancer. For more information, visit www.P65Warnings.ca.gov.
WARNING: While working in a hazardous area where you can be exposed to flying objects, fragments, and particles, primary protective devices such as safety glasses or goggles with side shields must be worn. Secondary protective devices such as a face shield is required in conjunction with primary protective devices during severe exposure to impact hazards.
WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.
Login and Registration Form