GF Exterior 450 Top Coat - Semi-Gloss Finish

GF Exterior 450 Top Coat - Semi-Gloss Finish

GF Arm-R-Seal Satin - you choose the quantity.

GF Arm-R-Seal Satin - Choose Your Quantity

GF Arm-R-Seal Gloss - Oil Based - Choose Your Quantity

In stock
SKU
GF-AGXX
Grouped product items
Product Name Qty
GF Arm-R-Seal Gloss - Oil Based - Pint
$25.00
GF Arm-R-Seal Gloss - Oil Based - Quart
$38.00

GF Arm-R-Seal Gloss - Oil Based - Choose Your Quantity

Arm-R-Seal Oil-Based Topcoats are made with the highest-quality urethane resin, making them extremely durable and long-lasting.

Formulated to be wiped on with a cloth or applied with a foam brush, this ambering finish penetrates to provide deep-down protection for that "natural" look.

Arm R Seal is a durable, oil-based topcoat made with high-quality urethane resins for exceptional durability. This easy-apply finish will bring out the natural beauty in hardwoods such as Walnut and Mahogany and will amber over time.

Can you Spray Arm-R-Seal?

Arm-R-Seal can be sprayed successfully, but we prefer hand application methods because spraying too much in one area is straightforward. If you choose to spray, use very thin coats and watch for runs (large drips that run down the side of your project).

If you notice a run, immediately wipe or brush it out. If you correct a run promptly, you will not see a mark. However, dried runs can be difficult to remove.

  • Wear a mask and work in a well-ventilated spray booth.
  • Size: Small Needle Nozzle (1mm)

Can An Oil Based Topcoat Such as Arm-R-Seal Be Thinned?

Although Arm-R-Seal rarely needs thinning because of its low viscosity, it can be thinned with up to 10% mineral spirits - more than that may thin the solids content too much. Thinned Arm-R-Seal will be diluted but can be stored without risk of separation.

More Information
BRANDGeneral Finishes
ColorClear - Gloss
QUANTITYAssorted
SKUGF-AGXX
SPECS:

Basic Features

  • Product Colors: Dries Amber
  • Base Type: Oil
  • Ambering: Yes
  • Sheen: Satin (25-35), Semi-Gloss (50-60), Gloss (80+)
  • Interior or Exterior: Interior only
  • Type: Urethane

Application

  • Coats: 3 coats
  • Application Method: Brush, Roll
  • Brushable: Yes
  • Usable over existing finishes: Yes
  • Sprayable: Yes
  • Spray Tip Sizes: HVLP 1.0mm-1.2mm

Dry Time

  • Dry Time - Touch: 12+ hr
  • Dry Time - Recoat: 12-24+ hr raw wood, 72+ hr existing finish until non-tacky. (Add more time with subsequent coats.)
  • Dry Time - Light Use: 7-10 days
  • Dry Time - Cure: 30 days

Contents

  • Can Sizes: Pints, Quarts, Gallons
  • Coverage: 50-60 sq.ft./pint, 100-125 sq.ft./quart, 400-500 sq.ft./gallon

Technical Data

  • Viscosity: Thin
  • Viscosity (cPs): 100-200
  • Weight Solids: 32%
  • VOC: US VOC
    Satin: 576.788 g/L
    Semi-Gloss: 576.231 g/L
    Gloss: 531.138 g/L

Durability

  • Durability (Highest, High, Medium, Low): Highest
  • Hardness (Koenig #): 77
  • Wear (Taber #): 57.10 mg loss
  • Water (5 max): 5
  • Chemical (105 max): 99
Prop 65

Prop 65 Warning

WARNING: This product can expose you to chemicals including Ethylbenzene, Naphthalene and Cumene, which are known to the State of California to cause cancer, and Toluene, which is known to the State of California to cause birth defects or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.

WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.

Write Your Own Review
You're reviewing:GF Arm-R-Seal Gloss - Oil Based - Choose Your Quantity
Your Rating

Prop 65 Warning

WARNING: This product can expose you to chemicals including Ethylbenzene, Naphthalene and Cumene, which are known to the State of California to cause cancer, and Toluene, which is known to the State of California to cause birth defects or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.

WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.

Contact Us