CrystaLac Extreme Protection Polyurethane Topcoat - Clear Satin Finish 1 Pint

CrystaLac Extreme Protection Polyurethane Topcoat - Clear Satin Finish 1 Pint

CrystaLac Extreme Protection Polyurethane Topcoat - Clear Satin Finish 1 Quart

CrystaLac Extreme Protection Polyurethane Topcoat - Clear Satin Finish 1 Quart

CrystaLac Extreme Protection Polyurethane Topcoat - Clear Gloss Finish 1 Pint

$22.99
Availability: In stock
SKU
CLU-GLOSS-P


CrystaLac® Extreme Protection Polyurethane Topcoat

Extreme Protection for Extreme Demands

Extreme Protection Polyurethane is a water based interior NON-YELLOWING, Environmentally Safe Top Coat that is Super Hard, Super Clear and Super Easy to Use.

FEATURES:

  • Scratch, Chemical, and Water Resistant
  • Self-Levels
  • Low Odor, Low V.O.C
  • Added UV stabilizers will keep dyes and stains brilliant and will help protect colors from fading
  • Dries crystal clear even over white finishes. Excellent for use as a chalk paint sealer.
  • CrystaLac Top Coats can be used over thoroughly dried oil or water-based stains, shellac, lacquer, Polyurethane or Acrylic.

APPLICATION:

  • Can be applied by either brushing or spraying (gravity feed or HVLP sprayer)
  • It is not necessary to sand between each top-coat layer. (All CrystaLac Top Coats will bond to the prior coat.)
  • If recoating over an old finish, scuff sand first and remove any surface contaminants such as dirt, waxes or polishes.
  • Usually 3 to 5 coats are sufficient to produce a beautiful, protective finish. Use more if desired.
  • Dry time is usually 30 min to 1 hour. Allow 2 to 4 hours before recoating.
  • Do not use stearated sandpaper or tack cloths. Do Not freeze. Do Not apply below 60 degrees.
  • Do not thin or clean with lacquer solvents or mineral spirits. Use soap and water for clean-up.

Coverage is approximately 400 to 500 sq. ft. per gallon.

CAUTION:

Keep out of reach of children! Do not ingest. Avoid contact with skin and eyes. Do not breathe vapors. Use with adequate ventilation. When spraying or sanding, use an OSHA approved mask. V.O.C. is less than 1.4 lbs. per gallon.

DISPOSAL:

Consult your local sanitation department. Do not dump on the ground.

WARNING: CrystaLac Company has chosen to provide a warning based on its knowledge about the presence of one or more listed chemicals without attempting to evaluate the level of exposure. Products marketed or sold by CrystaLac Company may contain listed chemicals at levels that are below the Proposition 65 level of concern, or could even be zero. However, out of an abundance of caution, CrystaLac Company has elected to place the Proposition 65 warning notification on all its products. Please see our Prop 65 for specifics on these products.

More Information
BRANDCrystaLac
ColorClear - Gloss
QUANTITYPint
SKUCLU-GLOSS-P
SPECS:

Coverage is approximately 400 to 500 sq. ft. per gallon.

Prop 65

Prop 65 WarningCrystaLac Company has chosen to provide a warning based on its knowledge about the presence of one or more listed chemicals without attempting to evaluate the level of exposure. Products marketed or sold by CrystaLac Company may contain listed chemicals at levels that are below the Proposition 65 level of concern or could even be zero. However out of an abundance of caution CrystaLac Company has elected to place the Proposition 65 warning notification on all its products. Listed Chemicals Present or Potentially Present in CrystaLac Company Products.

  • N-Methylprrolodone
  • Silica Crystaline
  • Carbon Black
  • Titanium Dioxide

For more information go to www.P65Warnings.ca.gov.

WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.

Prop 65 WarningCrystaLac Company has chosen to provide a warning based on its knowledge about the presence of one or more listed chemicals without attempting to evaluate the level of exposure. Products marketed or sold by CrystaLac Company may contain listed chemicals at levels that are below the Proposition 65 level of concern or could even be zero. However out of an abundance of caution CrystaLac Company has elected to place the Proposition 65 warning notification on all its products. Listed Chemicals Present or Potentially Present in CrystaLac Company Products.

  • N-Methylprrolodone
  • Silica Crystaline
  • Carbon Black
  • Titanium Dioxide

For more information go to www.P65Warnings.ca.gov.

WARNING: Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information go to www.P65Warnings.ca.gov/wood.

We found other products you might like!